Size

1.36″ (34.5mm)

Cylinder

Key Controlled Brass Dimple Cylinder

Keyway

Key Controlled Pick Resistant #06 Keyway

Keys

Includes 5 Dimple Keys & 1 Duplication Card

Furnished

Retaining Cap

Finish

26D Satin Chrome

Keying

Keyed Alike Up To 12 – KA 12

Warranty

Limited Lifetime Manufacturers Warranty

Polished Brass (Gold)

Using the application chart (shown below), identify vehicle as having a Type 1 or Type 2 ignition housing.

If Type 2, use the included pointed center punch to back out the ignition headless bolts if necessary.

Using the supplied awl/ice pick, insert the tip into the end of the roll pin and gently move it side to side in all directions. Use ice pick to center the roll pin within the hole.

Using 2 of the 3 color-coded thumb screws, attach the fixture to the front of the ignition housing. Use spacing washers if necessary.

Insert the Black Tee thumb screw into the 1/4-20 tapped hole and snug it up against the ignition cylinder.

Insert a short tube into the brass thumb screw and LIGHTLY snug in place using the set screw. Insert the long tube through the outer tube so that the flared tip is on the threaded end of the screw.

Insert the brass thumb screw assembly into the threaded hole seating the flared tip over the top of the roll pin. Verify the flared end is seated over the roll pin by trying to move the tip side to side.

Thread the brass thumb screw 1-2 full rotations, then lightly tap the back end of the tube inwards to ensure it’s fully seated over the roll pin.

Continue turning the brass thumb screw assembly until it comes to a definite stop. DO NOT OVER-TIGHTEN.

Tighten the set screw ONE FULL ROTATION ONLY.

Loosen the Black 1/4-20 Tee thumb screw.

Unthread the brass thumb screw assembly with roll pin now attached.

If Type 1, be sure to use the ice pick to lift the steering lock tail piece during cylinder removal.

Honda/Acura Ignition Roll-Pin Removal Kit Tips:

After using the ice pick and before installing the fixture, lightly tap on the cylinder itself (not the cylinder housing) with a hammer in the direction of the roll pin to ensure the roll pin is out as far as possible.

Since the roll pin is tapered on the ends, you can use the ice pick placed in the center of the roll pin and tap LIGHTLY to slightly flare out the roll pin to allow for greater “bite”. Be sure to follow tip #1 afterwards to “push” the roll pin out as far as possible.

Honda/Acura Ignition Roll-Pin Removal Kit Application Guide:

Make

Model

Years

Type

HONDA

Accord

1998-2002

2

2003-2012

1

Civic

2001-2011

1

Crosstour

2010-2012

1

CR-V & CR-Z

2002-2014

1

Element

2003-2011

1

Fit

2007-2014

1

Insight

2000-2006

2

2010-2014

1

Odyssey

1999-2004

2

2005-2013

1

Pilot

2003-2004

2

2005-2015

1

Prelude

1997-2001

2

Ridgeline

2006-2014

1

S2000

2000-2009

2

ACURA

CL

1997-2003

2

MDX

2001-2006

2

2007-2013

1

RDX

2007-2012

1

RSX

2002-2006

1

TL

1999-2003

2

2004-2013

1

TSX

2004-2014

1

Please Note:
This a 3rd Party Tool, We offer NO Support and NO Warranty This tool is very fragile and can be damaged from misuse, an inexperienced user and wrongful or too much pressure applied If the tool malfunctions or breaks in the first 30 days of purchase, we will offer a discount on another AccuReader but we will not refund or replace the tool

Application

Commercial or Residential single- and multi-family doors

Door Size

Use with 1-3/8 in. to 1-3/4 in. door

Cylinder

Removable KIK Key Controlled Brass Dimple Cylinder

Keyway

Key Controlled Pick Resistant #06 Keyway

Keys

Includes 5 Dimple Keys & 1 Duplication Card

Backset

Universal deadbolt fits 2-3/8 in. or 2-3/4 in. backset

Cover Ring

Heavy Duty Cover Ring Included

Finish

US3 Bright Brass

Keying

Keyed Alike Up To 12 – KA 12

Certification

Commercial Standard Certification: ANSI/BHMA A156.36-2010 Grade 1

Warranty

Limited Lifetime Manufacturers Warranty

WATCH DEMO VIDEO BELOW
WATCH HOW TO REKEY VIDEO BELOW

Premium Key Controlled KIK (Key-In-Knob) Cylinders
are machined engineered and manufactured to OEM specifications. Key Controlled cylinders are recommended as the new standard for behavioral health and ligature resistant applications. Each cylinder comes with a patented #06 keyway, 5 Key Controlled dimple keys and a duplication card. Designed to work with most Grade 1 and 2 Knob Lock, Lever Locksets and Deadbolts. The broad selection of models and components within our line provides you with the flexibility to cover numerous applications at a reasonable cost

Size

1.36″ (34.5mm)

Cylinder

Key Controlled Brass Dimple Cylinder

Keyway

Key Controlled Pick Resistant #06 Keyway

Keys

Includes 5 Dimple Keys & 1 Duplication Card Per Cylinder – 15 Keys & 3 Cards Total

Furnished

Retaining Cap per cylinder

Finish

26D Satin Chrome

Keying

Keyed Alike

Warranty

Limited Lifetime Manufacturers Warranty

For Mortise Cylinder

Measurements: 3″ x 6″

Satin Chrome Finish

Includes Faceplate, 4 Bolts , 4 nuts and 4 washers

For Mortise Cylinder

Measurements: 3″ x 6″

Polished Brass Finish

Includes Faceplate, 4 Bolts , 4 nuts and 4 washers

6-Pin BiLevel Cylinder w/2 Keys & Card

Utility patented key control provides protection from unauthorized duplication of keys

Nickel plated pins provide exceptional wear resistance and additional hardened stainless steel pins provide drill resistance

Retrofits into virtually any manufacturers’ locksets for cost effective improved security

High security and key control may be incorporated in a single system for cost effective system flexibility

Keys may be integrated with Hybrid proximity head for greater system retrofit

Yale Cam Type

US26 Finish (Satin Chrome)

Medeco Mortise cylinders have threads on the outside of the shell and are designed to be screwed into other manufacturer’s mortise lock cases. A cam on the back of the cylinder operates the lock mechanism and a set screw holds the mortise cylinder in place. Medeco Rim cylinders are used with auxiliary rim locks such as: surface mounted deadbolts, night latches, panic devices and jimmyproof locks (also know as vertical dropbolts or interlocking deadbolts).
Return Policy: We do not accept returns on unsealed products. In order to return a defective item a support ticket is needed. To receive a ticket, please contact Medeco directly at 800-839-3157 or visit their support page
here
. Once you have the ticket contact UHS Hardware for the return.

6-Pin BiLevel Cylinder w/2 Keys & Card

Utility patented key control provides protection from unauthorized duplication of keys

Nickel plated pins provide exceptional wear resistance and additional hardened stainless steel pins provide drill resistance

Retrofits into virtually any manufacturers’ locksets for cost effective improved security

High security and key control may be incorporated in a single system for cost effective system flexibility

Keys may be integrated with Hybrid proximity head for greater system retrofit

Adams Rite Cam Type

US3 Finish (Bright Brass)

Medeco Mortise cylinders have threads on the outside of the shell and are designed to be screwed into other manufacturer’s mortise lock cases. A cam on the back of the cylinder operates the lock mechanism and a set screw holds the mortise cylinder in place. Medeco Rim cylinders are used with auxiliary rim locks such as: surface mounted deadbolts, night latches, panic devices and jimmyproof locks (also know as vertical dropbolts or interlocking deadbolts).
Return Policy: We do not accept returns on unsealed products. In order to return a defective item a support ticket is needed. To receive a ticket, please contact Medeco directly at 800-839-3157 or visit their support page
here
. Once you have the ticket contact UHS Hardware for the return.

Secure your doorway with the
Premium Single Cylinder Contemporary Deadbolt Lockset
. Each lock features an adjustable latch.

Product is Grade 3 rated and includes 2 keys

Includes

Single Cylinder Deadbolt with Thumb Turn Interior

More Information Below

Handing

Non-Handed for Left or Right hand doors

Cylinder

Schlage SC1 Keyway or Kwikset KW1 Keyway with 2 brass keys

Door Thickness

1-3/8″ (35 mm) – 1-3/4 ” (44.5 mm)

Backset

Adjustable Backset 2-3/4″ (70 mm) to 2 3/8″ (60 mm)

Bolt

1″ (26 mm ) throw – round cornered

Material

Brass

Strike

1″ (25.5 mm) x 2 -1/4″(57 mm) strike

Finish

613 – US10B – Oil Rubbed Bronze

Certifications

Grade 3

Manufacturer Warranty

Limited lifetime mechanical warranty

Keyed Alike

Up to 4 KA4

Packaging

Each Deadbolt is Boxed with 2 keys

Each Carton of 4 Includes 4
separate
boxed Deadbolts ( All Keyed Alike)

WATCH DEMO VIDEO BELOW