5in * 11in Base Plate

Strong Neodymium Magnets

Reversible Vise Base

Reversible Vise Wheel for recessed lip or flush edge lip

Easy Tighten Thumb Screws

If you do eeprom work this is perfect for you. Our new Circuit Board Vise was specifically designed for locksmiths by locksmiths doing eeprom work. It is by far the most versatile and secure vise on the market today. ) Designed to securely hold any size automotive circuit board in virtually any position.
Instructions:

Place the edge of circuit board into the clamp’s edge, making sure no components are underneath the clamp jaws.

With the rotation screws slightly loosened, tighten the clamp screws to grip the circuit board.

Once the clamp jaws are tightened and the rotation screws slightly loosened, place assembly onto the base plate.

Rotate the circuit board to desired angle and tighten rotation screws.

Please Note:
This a 3rd Party Tool, We offer NO Support and NO Warranty This tool is very fragile and can be damaged from misuse, an inexperienced user and wrongful or too much pressure applied If the tool malfunctions or breaks in the first 30 days of purchase, we will offer a discount on another AccuReader but we will not refund or replace the tool

Using the application chart (shown below), identify vehicle as having a Type 1 or Type 2 ignition housing.

If Type 2, use the included pointed center punch to back out the ignition headless bolts if necessary.

Using the supplied awl/ice pick, insert the tip into the end of the roll pin and gently move it side to side in all directions. Use ice pick to center the roll pin within the hole.

Using 2 of the 3 color-coded thumb screws, attach the fixture to the front of the ignition housing. Use spacing washers if necessary.

Insert the Black Tee thumb screw into the 1/4-20 tapped hole and snug it up against the ignition cylinder.

Insert a short tube into the brass thumb screw and LIGHTLY snug in place using the set screw. Insert the long tube through the outer tube so that the flared tip is on the threaded end of the screw.

Insert the brass thumb screw assembly into the threaded hole seating the flared tip over the top of the roll pin. Verify the flared end is seated over the roll pin by trying to move the tip side to side.

Thread the brass thumb screw 1-2 full rotations, then lightly tap the back end of the tube inwards to ensure it’s fully seated over the roll pin.

Continue turning the brass thumb screw assembly until it comes to a definite stop. DO NOT OVER-TIGHTEN.

Tighten the set screw ONE FULL ROTATION ONLY.

Loosen the Black 1/4-20 Tee thumb screw.

Unthread the brass thumb screw assembly with roll pin now attached.

If Type 1, be sure to use the ice pick to lift the steering lock tail piece during cylinder removal.

Honda/Acura Ignition Roll-Pin Removal Kit Tips:

After using the ice pick and before installing the fixture, lightly tap on the cylinder itself (not the cylinder housing) with a hammer in the direction of the roll pin to ensure the roll pin is out as far as possible.

Since the roll pin is tapered on the ends, you can use the ice pick placed in the center of the roll pin and tap LIGHTLY to slightly flare out the roll pin to allow for greater “bite”. Be sure to follow tip #1 afterwards to “push” the roll pin out as far as possible.

Honda/Acura Ignition Roll-Pin Removal Kit Application Guide:

Make

Model

Years

Type

HONDA

Accord

1998-2002

2

2003-2012

1

Civic

2001-2011

1

Crosstour

2010-2012

1

CR-V & CR-Z

2002-2014

1

Element

2003-2011

1

Fit

2007-2014

1

Insight

2000-2006

2

2010-2014

1

Odyssey

1999-2004

2

2005-2013

1

Pilot

2003-2004

2

2005-2015

1

Prelude

1997-2001

2

Ridgeline

2006-2014

1

S2000

2000-2009

2

ACURA

CL

1997-2003

2

MDX

2001-2006

2

2007-2013

1

RDX

2007-2012

1

RSX

2002-2006

1

TL

1999-2003

2

2004-2013

1

TSX

2004-2014

1

Please Note:
This a 3rd Party Tool, We offer NO Support and NO Warranty This tool is very fragile and can be damaged from misuse, an inexperienced user and wrongful or too much pressure applied If the tool malfunctions or breaks in the first 30 days of purchase, we will offer a discount on another AccuReader but we will not refund or replace the tool

Product Type: Pick & Decoder

OE Part #: IRPRF

This pack includes 10 clamp tube sets to be used with our Honda/Acura Ignition Roll Pin Removal Kit.

Compatible with the following:

1998 – 2012 Honda Accord

2001 – 2011 Honda Civic

2010 – 2012 Honda Crosstour

2002 – 2014 Honda CR-V

2011 – 2015 Honda CR-Z

2003 – 2011 Honda Element

2007 – 2014 Honda Fit

2000 – 2006 Honda Insight

2010 – 2014 Honda Insight

1999 – 2013 Honda Odyssey

2003 – 2015 Honda Pilot

1997 – 2001 Honda Prelude

2006 – 2014 Honda Ridgeline

2000 – 2009 Honda S2000.

1997 – 2003 Acura CL

2001 – 2013 Acura MDX

2007 – 2012 Acura RDX

2002 – 2006 Acura RSX

1999 – 2013 Acura TL

2004 – 2014 Acura TSX.

Please Note:
This a 3rd Party Tool, We offer NO Support and NO Warranty This tool is very fragile and can be damaged from misuse, an inexperienced user and wrongful or too much pressure applied If the tool malfunctions or breaks in the first 30 days of purchase, we will offer a discount on another AccuReader but we will not refund or replace the tool

Up to 15x magnification to help you see the tiniest details

Use this magnifier for reading maps, doing fine stitch work, or magnifying virtually any text to make it more visible and easier to read

Compact design for carrying in a purse or bag

This magnifier packs a lot of punch in a small footprint

Tuck it in a bag for traveling or tote it in your pocket for ease of reading labels at the grocery store

Ergonomic handle is molded for an easy grip

Read over small print for hours without hand fatigue

Map reading magnifying glass with light: 3x, 10x, 45x

The handle is comfortable and easy to grip to lessen tension while you read

Read in the dark with full magnification up to 15x with the small piece and 3x with the large piece

The lighted design is ideal for traveling by car or for reading in other darkened areas

The fast switch turns the light on and off quickly.

Item Weight: 0.02 Pounds

Item Dimensions LxWxH: 7.9 x 3.6 x 1.4 inches

Color: Black

Blu-Mol® Professional Bi-Metal Door Lock Installation Kit makes easy work of installing a door lock on most wood or metal doors. 3 easy steps: Position, Bore, and Assemble. Adjusts to 1-3/8″ and 1-3/4″ door thickness. Backsets adjust to 2-3/8″ and 2-3/4″.

Includes: 1″ Hole Saw, 2-1/8″ Hole Saw, Guide, Assembled mandrel, Mandrel adapter.

Door Lock Installation Kits make installing a door lock fast, easy and accurate.

3 Easy Steps: Position, Bore, and Assemble.

Dual-sided for faster drilling.

Manufacturer: AeroLock

Made from High-Quality Stainless Steel, the Aerolock Multi-Function Clip Removal Tool makes your job faster & easier:

Removes Kwikset spindles

Detent pusher for commercial & residential locks

Removes C and E clips on Kwikset, Schlage, and import locks

Cylinder removal tool

This Fixing Tool Flip Key Vice holds most remote key fobs safely and allows to remove and insert roll pins to change blades.

Use it to quickly disassemble/assemble the remote keys.
Please Note:
This a 3rd Party Tool, We offer NO Support and NO Warranty. This tool is very fragile and can be damaged from misuse, an inexperienced user and wrongful or too much pressure applied. If the tool malfunctions or breaks in the first 30 days of purchase, we will offer a discount on another Klom tool but we will not refund or replace the tool

Made by high-quality steel, comes in a hard plastic box, strong protection, it is a professional tool for locksmith.

With the pliers, it’s very easy to remove the pin and take off the blade for cutting.

Package included :

1 x Auto Remote Key Blade Pin Disassembling Clamp

2 x Removal pinheads

Please Note:
This a 3rd Party Tool, We offer NO Support and NO Warranty. This tool is very fragile and can be damaged from misuse, an inexperienced user and wrongful or too much pressure applied. If the tool malfunctions or breaks in the first 30 days of purchase, we will offer a discount on another Klom tool but we will not refund or replace the tool

This is not your ordinary pair of auto cap pliers. The curved end of the jaw follows the curved outside surface of the face cap to minimize the likelihood of damaging or disfiguring the outside surface of the cap.

When the lock is ready to reassemble, the old cap can be reused using the recessed inside jaws. These pliers are designed to stake spring covers, such as those used on GM sidebar locks, BMW etc.

Please Note:
This a 3rd Party Tool, We offer NO Support and NO Warranty. This tool is very fragile and can be damaged from misuse, an inexperienced user and wrongful or too much pressure applied. If the tool malfunctions or breaks in the first 30 days of purchase, we will offer a discount on another Klom tool but we will not refund or replace the tool