Supports make new key with the ignition switch.

Can perform All Keys Lost (AKL) and Spare Key Functions.

The ISN from the DME will be required in any All Keys Lost (AKL) Situations.

Mileage Correction

FEM Coding Backup

FEM Coding Restore for the same vehicles

Technical Service Bulletins & Recalls for domestic vehicles – 1992 to present.

Service Information – 1992 to present.

Wiring information – 1996 to present.

Diagnostic information – 1992 to present.

Online functionality of FCA diagnostic scan tool (also requires an active wiTECH Scan Tool and Vehicle Reprogramming Subscription)

NOTE:
Some Wiring and Diagnostic procedures may be found under the Service Information Tab.
Body repair Information, Training Materials, Ability to view JTEC, SBEC and FCC related OBD II calibration information.
Vehicle controller reprogramming, Flash Matrix with Flash part numbers and part supercedance.
Capability to download Flash files for updating controllers. (also requires an active wiTECH Scan Tool and Vehicle Reprogramming Subscription)
Note: If you are purchasing a subscription to only Flash a module on a vehicle, verify that a Flash is available by referencing one of the following PDF files. (also requires an active wiTECH Scan Tool and Vehicle Reprogramming Subscription)
Flash Availability – FCA Scan Tools
Flash Availability – J2534/Pass Thru Device

wiTECH 2.0 requires a subscription to be used with a microPod or Validated J-2534 pass thru device.

wiTECH 2.0 is currently available to the USA, Canada, Mexico, Guam, Puerto Rico

wiPODs will not work at all with wiTECH 2.0, you must upgrade your device to a Secure microPod II. (Serial numbers WSP-31560 and newer are secure)

NOTE:
Flash programming and service information requires a separate subscription to
Tech Authority.

Can copy ID48 chip data without OBD connection to the car incl. VW 2015-2017

Cannot program a new key when all keys are lost

The KeyTool must have software V1.2.5 (2017-2-23) or later

If software is already on one machine it can be bound to another.

Supports all car types with 48 transponder chip without OBDII

Cannot support Keyless go system or MQB platform

PLEASE NOTE:

If you are using the Keytool, you DO NOT need the emulator to clone any 48

If you are using the VVDI2 – you DO need the emulator to clone 96 bit 48

Daily Subscription: 5 day

minimum

purchase for
78$
with
$15.60

for
each
additional day.
Buying single software packs or software pack groups;
You can buy the most popular applications for your market which will be cheaper than spending credits each time. You may still purchase often used software packs and use rare applications with your credits (both systems can be used in the same device).

LIFS;

Unlimited use for all Zed-FULL plus applications(exceptions may apply ie: remote unlocking and online pin code applications) for certain time of period like 3 months, 6 months or 1 year moreover during subscription period, all software updates will be delivered free of charge.

Daily LIFS;

Unlimited use for all Zed-FULL plus applications(exceptions may apply ie: remote unlocking and online pin code applications) for24 hours. Minimum 5 days of daily LIFS can be purchased each time.

Group LIFS;

Application specific subscription, for example, BMW obd programming group

LIFS:

includes all BMW obd applications. Good when Zed-FULL plus is used for specific applications and/or car brands only.

*PLEASE NOTE: This is only the subscription service, The machine is sold separately*
Zed-Full Tech Support: 512-887-3948
Zed-FULL Registration Process:
Zed-FULL Daily LIFS:

Annual Maintenance Subscription

Please enter AVDI Serial Number # in the below section when adding to your cart. This is required to complete the order processing.

Your initial purchase of the AVDI interface includes one year of software updates for the basic diagnostic suite, tools and our online services.
The AMS allows you to keep up to date with software applications and maintain usage of our online services.
The Annual Maintenance Subscription is a renewable one year subscription. ***To avoid higher costs for AMS, please renew each year.
The Annual Maintenance Subscription does not provide any support coverage this is provided separately by the Support Plan (SPS).
An Active AMS is required to purchase additional special functions for your AVDI.
The normal turnaround time for software link processing, is 24-48 hours during business hours

We are happy to announce that we are adding even more FREE functionalities for all AVDI users with active AMS!

From now on, you can access a selection of ANxxx licenses (legacy functionalities) with the basic software for FREE. These solutions allow key programming and mileage calibration, as well as facilitate module replacement in VAG Immo III and III+ vehicles. This goes for the following special functions and licenses:

AN002 and AN003 –
reading CAN TP2.0 dashboards 2003-2008.
They are used for PIN/CS reading, mileage calibration on these dashboards in all VW/Seat/Skoda 2003-2008 (Immo III/III+ cars). This functionality is mainly used for preparing keys and mileage calibration.
AN004 –
Allows to manually change the Immo data for the modules above. This can be used to adapt a dashboard (immobilizer) for all VW/Seat/Skoda 2003-2008 (Immo III/III+ vehicles).
AN005 –
Used for new ECU adaptation in Immo III (excluding Immo III+) through adaptation by diagnostics on channel 50.
AN006 –
Allows reading EEPROMs on dashboards that use K-Line protocol. These are all 1998-2003 dashboards (VDO, Magneti Marelli, Motometer, on VW/Seat/Skoda), as well as Bosch RB4/RB8 dashboards (RB4 – 2001-2004 VW Golf/Audi A4, RB8 – Audi A4 2004-2008) . You can extract PIN/CS to program keys and calibrate mileage.
AN007 –
Used for reading the EDC15 (2000-2004) and ME7 (2000-2006) ECUs.
Also, extracting CS/PIN which can be used for key learning and module replacement (through adaptation by diagnostics on channel 50).
AN010 –
Allows reading the EEPROM of Airbags that use the K-Line protocol (1997-2004).
AN012 –
Allows odometer replacement on EDC16 (2004-2008).
AN014 –
Used for EDC17 PIN reading (excluding CS) – used for programming dealer keys (excluding preparing) for EDC17/MED17 2007-2010.
AN018/AN019 –
Allows reading EEPROM of EZS-Kessy on Audi 4F (A6 2003-2008, Q7 2005-2008). Used for extracting PIN/CS and key programming for these vehicles.
AN021 –
Used for reading the ME7 EEPROM via CAN protocol. These ECUs are used in vehicles such as the Audi TT 2003-2010. This functionality allows extracting the PIN/CS, which are used for key programming.
AN023 –
Used for Crafter Key programming in vehicles 2006-2012 equipped with EDC16.
AN024 –
Allows key programming for all Immo III/III+ vehicles, if PIN/CS is known (can be read with one of the other licenses) and a dealer key is present.
АN025 –
Allows reading the PIN/CS from EDC16/MED9/Simos PPD/Simos 7.x ECUs.
AN026 –
Used for dealer key preparation and programming (for all Immo III/III+ vehicles). It is used to find the 7th byte of the Immobilizer (if the Component Security bytes from the ECU can be read).
AN027 –
same as AN018/19, but extended to A6 2003-2010, Q7 2005-2014.
AN028/AN029 –
Allows UDS Dashboard Reading – VDO 2008-2015, JCI 2008-2012, Magneti Marelli 2006-2014. These are all used in VW/Seat/Skoda 2008-2013, as well as Audi A1/Q3. It is used to calibrate mileage and program keys (spare key and All Keys Lost).
What’s more, now the special functions for
JLR – JL003 and JL004 will be available to every AVDI user with active AMS.
This means that mileage calibration and key programming for Jaguar and Land Rover vehicles up to 2018 is now part of the basic AVDI software.
• Spare key programming
• ALL KEYS LOST key programming
• Remote control and keyless programming are part of the procedure, so no extra steps are required.
Supported models for key learning are equipped with the following KVM types:
• DPLA
• FK72
• HPLA
Supported models for mileage recalibration (including but not limited to):
Land Rover
• Evoque (L538) – LL and HL (2- and 4-door models)
• Range Rover Sport (L494)
• Range Rover (L405) (including long wheel base)
Jaguar
• F-Type Convertible and Coupe
• XF (X250)
• XJ (X351)
• XK (X150)
• XKR (X150)
The
FN012 special function now also becomes a part of the basic AVDI package.
This means that the following is available For FCA vehicles up to 2012 without the need for additional purchases:
• Key programming by OBDII
• Transponders/Keys preparation by dump of Immobiliser
• BCM – Configuration data read and update, PIN, component protection data
• BCM Read/Update ConfData by OBDII
Supported models for key programming:
• Fiat, Alfa, Lancia – Alfa 147, Mito; Fiat 500, Bravo, Grande punto, Croma, Doblo, Ducato, Fiorino, Idea, Palio, Panda, Stilo; Lancia Thesis, Delta.
Supported units:
• BCM Delphi (93C66) – NOTE: PIN Code is required!
• BCM Marelli (912DG128, 3K91D)
• BCM Marelli (9S12DG256, 1K79X)
• BCM Marelli (NEC 70F3237/70F3378,95160)
• BCM Marelli (NEC 70F3633,95320)
• BCM Siemens (9S12DG128)

ALL SALES OF ABRITES PRODUCTS HARDWARE AND SOFTWARE ARE FINAL!

Can copy ID48 chip data with OBD Connection

Can program a new key when all keys are lost

VVDI2 device must have VW 4th software activated

Supports all car types with 48 transponder chip with OBDII

Can support Keyless go system and MQB platform

Once bought, it can be bound from VVDI2 to the Key Tool without additional purchase, but not the other way around.

Key Tool Max
,
VVDI Key Tool Mini
,
Key Tool Max Pro
and

VVDI Keytool
,

make sure you have

XHS-VVDI96BIT

authorization!
VVDI2

owners require either

XHS-VVDI96BIT

or

XHS-VVDIOBD

in order to use ID48 tokens for 48 cloning!
Compatibility:

Key Tool Max

VVDI Key Tool Min

Key Tool Max Pro

VVDI2

Key Tool Plus Pad

Yearly Subscription for Supervag Programming Machine

*PLEASE NOTE: This is only the subscription service, The machine is sold separately*